1 Introduction

This vignette demonstrates how to use scp to report missing values, following our recommendations in Vanderaa and Gatto (2023). Briefly, we recommend reporting at least 4 metrics:

  • Total sensitivity, i.e. the total number of features found in the dataset
  • Local sensitivity, i.e. the number of features per cell
  • Data completeness, i.e. the proportion of values that are not missing
  • Number of samples

We will also demonstrate how to estimate total sensitivity when the number of samples is too low and how to report data consistency using the distribution of the Jaccard indices.

In this vignette, we will assume you are familiar with the scp framework. If this is not the case, we suggest you first read the introduction vignette.

2 Minimal data processing

First, we load the scp package and retrieve a real-life dataset from the scpdata package.

leduc <- leduc2022()

Next, we reduce the size of the dataset to the 30 first acquisitions. This allows for a fast execution of the code for this vignette while still being a representative demonstration on a real dataset. We also keep only the feature annotations that will be used later in the vignette.

leduc <- leduc[, , 1:30]
#> Warning: 'experiments' dropped; see 'drops()'
#> harmonizing input:
#>   removing 8057 sampleMap rows not in names(experiments)
#>   removing 1872 colData rownames not in sampleMap 'primary'
leduc <- selectRowData(leduc, c(
    "Sequence", "Leading.razor.protein", "Reverse",
    "Potential.contaminant", "PEP"

This is the actual minimal processing: 1. filtering contaminant and low-quality features 2. replacing zeros by missing values 3. keep only samples that correspond to single cells 4. remove the feature absent in all samples 5. aggregate PSMs to peptides 6. join all runs in a single large assay

## 1.
leduc <- filterFeatures(leduc, ~ Reverse != "+" &
                           Potential.contaminant != "+" &
                           PEP < 0.01)
## 2.
leduc <- zeroIsNA(leduc, i = names(leduc))
## 3.
leduc <- subsetByColData(
    leduc, leduc$SampleType %in% c("Monocyte", "Melanoma")
## 4.
leduc <- filterNA(leduc, i = names(leduc), pNA = 0.9999)
leduc <- dropEmptyAssays(leduc)
## 5.
leduc <- aggregateFeatures(
    leduc, i = names(leduc), name = paste0("peptides_", names(leduc)),
    fcol = "Sequence", fun = colMedians
## 6.
leduc <- joinAssays(
    leduc, i = grep("^peptides_", names(leduc)), name = "peptides"

What about proteins? if we were interested in reporting missing values at the protein level, we simply need to change fcol = "Sequence" to fcol = "Leading.razor.protein" in aggregateFeatures().

3 Report missing values

We can now compute the metrics of interest. We recommend computing these for each cell type separately, since biological properties specific to the cell type could influence the outcome. You can perform this using reportMissingValues(). We provide the dataset and point towards the assay with the peptide quantification matrix (peptides). The metrics are computed based on the cell annotation SampleType that is available in the colData.

reportMissingValues(leduc, "peptides", by = leduc$SampleType)
#>          LocalSensitivityMean LocalSensitivitySd TotalSensitivity Completeness
#> Monocyte             2664.213           367.7552             7028    0.3751356
#> Melanoma             2958.851           430.9701             7093    0.4166223
#>          NumberCells
#> Monocyte         197
#> Melanoma         195

4 Advanced criteria

4.1 Jaccard index distribution

The Jaccard index between a pair of cells is the number of features shared by the two cells divided by the number of features identified in any of the two columns. This provides a good measure of how consistent the identifications are across single-cells. Again, biological differences between cell types may decrease the consistency between single cells and we therefore suggest to compute the Jaccard index for each cell type separately. We compute the Jaccard index using jaccardIndex().

ji <- jaccardIndex(leduc, "peptides", by = leduc$SampleType)

The function returns a data.frame that we visualize using the ggplot2 package.

ggplot(ji) +
    aes(x = jaccard) +
    geom_histogram() +
    facet_grid(~ by)
#> `stat_bin()` using `bins = 30`. Pick better value with `binwidth`.

The Jaccard indices peak around 50 %, meaning that about half of the features are consistently found across single-cells within the same cell type. Note also that some pairs of cells have consistency above 75 %. These are pairs of cells from the same acquisition runs that were multiplexed together with TMT labelling.

4.2 Assessing the total sensitivity

To assess whether we can accurately estimate the total sensitivity, we generate a cumulative sensitivity curve (CSC). More precisely, we sample the identification matrix for an increasing number of cells (or runs) and count the number of distinct features found across the sampled cells. We repeat each sampling multiple times to account for the stochasticity of the approach. The approach is implemented in cumulativeSensitivityCurve(). Again, we compute the curve for each cell type separately. In the leduc dataset, several cells are acquired in an MS run. When a features is identified in a cell, it is most of the time also identified in all other cells of that run, and this will distort the cumulative sensitivity curve. Therefore, the function provides a batch argument to account for this. Finally, nSteps defines the number of random draws with increasing sample size, and niters defines how many times each draw must be iterated.

csc <- cumulativeSensitivityCurve(leduc, "peptides", by = leduc$SampleType,
                                  batch = leduc$Set, niters = 10,
                                  nsteps = 30)

The function returns a data.frame that we visualize using the ggplot2 package.

(plCSC <- ggplot(csc) +
    aes(x = SampleSize, y = Sensitivity, colour = by) +
    geom_point(size = 1))

The cumulative sensitivity does not reach a plateau. This means that we underestimated the total sensitivity in the previous section. We use predictSensitivity() to predict the total sensitivity from these curves. The function fits an asymptotic regression model to assess the relationship between the sensitivity and the sample size. Then, it uses the model to predict the sensitivity for any sample size. (supplied through nSamples). The function requires the data.frame generated by cumulativeSensitivityCurve(). To assess the quality of the fit, we first predict the sensitivity for the range of sample size.

predCSC <- predictSensitivity(csc, nSample = 1:30)
plCSC + geom_line(data = predCSC)